## Line Chart: NMSE vs. Frequency for Different Rooms ### Overview The image presents a line chart comparing the Normalized Mean Squared Error (NMSE) in decibels (dB) across different rooms (Room B, VR Lab, List. Room, and Prod. Room) as a function of frequency, ranging from approximately 30 Hz to 300 Hz. The chart aims to visualize the performance or accuracy of a system or measurement within each room at various frequencies. ### Components/Axes * **X-axis:** Frequency (Hz), ranging from 30 to 300 Hz. The axis is linearly scaled. * **Y-axis:** NMSE (dB), ranging from -25 dB to 0 dB. The axis is linearly scaled. * **Legend:** Located in the top-right corner, identifying the four data series: * Blue Line: Room B * Green Line: VR Lab * Black Line: List. Room * Red Line: Prod. Room ### Detailed Analysis The chart displays four distinct lines, each representing a room. * **Room B (Blue Line):** This line exhibits a strong upward trend from approximately -22 dB at 30 Hz to around -2 dB at 300 Hz. The line is relatively smooth, with some fluctuations. At 30 Hz, the NMSE is approximately -22 dB. At 60 Hz, it's around -14 dB. At 100 Hz, it's approximately -8 dB. At 200 Hz, it's around -4 dB. At 300 Hz, it's approximately -2 dB. * **VR Lab (Green Line):** This line starts at approximately -4 dB at 30 Hz, dips to around -10 dB at 40 Hz, then rises to approximately 0 dB at 300 Hz. It shows more variability than the other lines. At 30 Hz, the NMSE is approximately -4 dB. At 60 Hz, it's around -8 dB. At 100 Hz, it's approximately -6 dB. At 200 Hz, it's around 0 dB. At 300 Hz, it's approximately 0 dB. * **List. Room (Black Line):** This line remains relatively stable, fluctuating between approximately -2 dB and 2 dB across the entire frequency range. It shows minimal change with frequency. At 30 Hz, the NMSE is approximately -2 dB. At 60 Hz, it's around 0 dB. At 100 Hz, it's approximately 0 dB. At 200 Hz, it's around 0 dB. At 300 Hz, it's approximately 0 dB. * **Prod. Room (Red Line):** This line starts at approximately -2 dB at 30 Hz, dips to around -6 dB at 50 Hz, then rises to approximately 0 dB at 300 Hz. It is similar to the VR Lab line, but generally remains slightly lower in NMSE values. At 30 Hz, the NMSE is approximately -2 dB. At 60 Hz, it's around -4 dB. At 100 Hz, it's approximately -2 dB. At 200 Hz, it's around 0 dB. At 300 Hz, it's approximately 0 dB. ### Key Observations * Room B exhibits the most significant increase in NMSE with increasing frequency. * List. Room demonstrates the most stable performance across all frequencies, with consistently low NMSE values. * VR Lab and Prod. Room show similar trends, with NMSE values fluctuating more than List. Room but less than Room B. * All rooms converge towards an NMSE of approximately 0 dB at 300 Hz. ### Interpretation The chart suggests that the performance or accuracy of the system being measured is highly dependent on both the room and the frequency. Room B appears to be the most sensitive to frequency changes, exhibiting a substantial increase in error as frequency increases. List. Room, on the other hand, provides the most consistent and accurate results across the tested frequency range. The convergence of all lines at higher frequencies (around 300 Hz) might indicate a limitation of the system or measurement technique at those frequencies, or a shared characteristic of the rooms at higher frequencies. The NMSE values represent the difference between predicted and actual values, so lower NMSE values indicate better performance. The data suggests that for applications requiring accuracy across a broad frequency range, List. Room would be the preferred environment. The differences in NMSE between the rooms could be due to variations in acoustic properties, noise levels, or other environmental factors.